Porsche 2015 911 GT3 Cup Скачать руководство пользователя страница 314

Страница: 314 / 321

Maintenance

7.5

Body

•

Check the body for cracks and damage near the suspension and
engine/gearbox mounting points

•

Check wing support brackets for cracks and damage

•

Check seat and seat rail for damage, tightness and function

7.5.1

Airjack system

Porsche Motorsport recommends overhauling after two years or 2,000 strokes.

•

Only clean air jack piston with silicone grease or spray

•

Regularly check the air jacks for mechanical damage

Other maintenance work is only to be performed by the manufacturer! Refer to the

appendix for the manufacturer’s detailed information material.

7.5.1

Version: 16.12.2014

313

911 GT3 Cup (991)

MY 2015

Содержание 2015 911 GT3 Cup


































































































































































































































































































































Результаты поиска

Содержание 2015 911 GT3 Cup

Отзывы:

Бренды по названию

Популярные бренды

Porsche 2015 911 GT3 Cup, Техническое руководство

Результаты поиска

Содержание 2015 911 GT3 Cup

Отзывы:

Бренды по названию

Популярные бренды