Porsche 2015 911 GT3 Cup Скачать руководство пользователя страница 107

Страница: 107 / 321

Powertrain

2.9.10

Reverse idler gear

The needle bearing sleeve (2) must be assembled first during reconstruction. Heat

the reverse idler gear (3) to 130° (266 F) C for 30 minutes and press in the needle

bearing sleeve with tool no. 32

Heat-resistant gloves must be worn for any work with

hot items because of the risk of burning.

Secure the needle bearing sleeve (2) with the locking ring (1)

Insert reverse idler gear (3) with bearing spindle (4) and shift fork (Figure 2.9.9.2);

the gearshift shaft must be in the neutral position to allow sufficient space for

inserting

WARNING

2.9.10.2

2.9.10.1

Version: 16.12.2014

106

911 GT3 Cup (991)

MY 2015

Содержание 2015 911 GT3 Cup


































































































































































































































































































































Результаты поиска

Содержание 2015 911 GT3 Cup

Отзывы:

Бренды по названию

Популярные бренды

Porsche 2015 911 GT3 Cup, Техническое руководство

Результаты поиска

Содержание 2015 911 GT3 Cup

Отзывы:

Бренды по названию

Популярные бренды