Porsche 2015 911 GT3 Cup Скачать руководство пользователя страница 20

Страница: 20 / 321

Engine

911 GT3 Cup (991)

MY 2015

1.4.3

Coolant

Upon delivery, the cooling system is filled with 11 liters (11.6 qts.) of water and 11

liters (11.6 qts.) of low temperature/freezing protection, ensuring a low

temperature/freezing protection up to -30° C (-22° F).

For all racing events, Porsche Motorsport recommends substituting the factory filled

coolant with 20 liters (21 qts.) of water and 2 liters (2.1 qts.) of corrosion protection

(spare part no. 997.106.907.90). Corrosion protection protects the water-carrying

parts from corrosion, reduces cavitation, lubricates the water pump and raises the
boiling point of the coolant.

For support races to the Formula 1 world

championship, the coolant has to be substituted as

described below.

Approx. 20 liters (21 qts.) of water plus at least 2 liters

(2.1 qts.) of corrosion protection, spare part no.

997.106.907.90

Filling quantity: 22 liter (23.2 qts.)

1.4.4

Filling the cooling system

Refer to chapter 7 „Maintenance“.

1.4.5

Races at low temperatures

For operations at low temperatures, the radiators much be masked in order to

operate the engine at optimum operating temperature. The following procedure must

be observed:

First, cover the central radiator with masking tape (starting from the top). If this is not

sufficient, cover up to 2/3 of the two outer radiators (starting from the top). It is not

permitted to cover the side radiators completely, as their exhaust is used for cooling

the brakes.

NOTE

Version: 16.12.2014

Содержание 2015 911 GT3 Cup


































































































































































































































































































































Результаты поиска

Содержание 2015 911 GT3 Cup

Отзывы:

Бренды по названию

Популярные бренды

Porsche 2015 911 GT3 Cup, Техническое руководство

Результаты поиска

Содержание 2015 911 GT3 Cup

Отзывы:

Бренды по названию

Популярные бренды