Porsche 2015 911 GT3 Cup Скачать руководство пользователя страница 170

Страница: 170 / 321

Chassis

3.9

Balance bar replacement kit

3.9.1

Replacing the trunnion

•

Remove balance bar see chapter 3.9.2

•

Remove both circlipses from either end

•

Remove the trunnion and both bearings by using a light press

•

Clean the bore of any dirt

•

Replace the lower circlip

•

Push the lower bearing down the bore

•

Drop the trunnion into the bearing

•

Push the bearing and the circlip down until the circlip pops into the groove,
the trunnions should have axial clearance and should not be tight

3.9.2

Replacing the balance bar

•

Remove the R-clips, spacers, circlips and clevises from the balance bar

•

Remove the balance bar

The retaining ring and circlip should be replaced after

each dismantling

•

Screw the new balance bar fully into the trunnion in the housing

•

Push a new retaining ring on the balance bar

Do not over stress the retaining ring, if it deforms it will

not perform correctly

•

Set the balance bar back to center (see chapter “balance bar setup” 3.8.1)

•

The installation is carried out in reverse order

After each race or training to prevent from dirt the

needle bearing should be covered with a doughy fat

NOTE

3.8.2.3

3.8.2.1

3.8.2.2

Version: 16.12.2014

169

911 GT3 Cup (991)

MY 2015

Содержание 2015 911 GT3 Cup


































































































































































































































































































































Результаты поиска

Содержание 2015 911 GT3 Cup

Отзывы:

Бренды по названию

Популярные бренды

Porsche 2015 911 GT3 Cup, Техническое руководство

Результаты поиска

Содержание 2015 911 GT3 Cup

Отзывы:

Бренды по названию

Популярные бренды