Porsche 2015 911 GT3 Cup Скачать руководство пользователя страница 220

Страница: 220 / 321

Bodywork

911 GT3 Cup (991)

MY 2015

Preparation for replacing the strut dome

These instructions describe how to remove the left front strut dome. Perform the

operations on the right side inversely. The estimated time for the described repair is

approximately three hours.

Remove the following parts:

•

Fender left

•

Headlight left

•

Wheel arch liners left

•

Underbody, front

•

Chassis left

•

Front bumper

•

Fuel tank

•

Brake lines left

•

Draining the coolant, front

•

Water cooler and cooling hoses left

•

Steering gear

•

Air jack, front and cross member

•

Master cylinder, remove if required

Removing/drilling out the strut dome

The service life of a drill is about 14 to 20 rivets.

Deeply mark the rivets (1) with the center.

Drilling out the rivets from the rear makes the process much easier.

Use drilling fluid to prolong the drill’s service life.

4.15.2.2

Version: 16.12.2014

219

Содержание 2015 911 GT3 Cup


































































































































































































































































































































Результаты поиска

Содержание 2015 911 GT3 Cup

Отзывы:

Бренды по названию

Популярные бренды

Porsche 2015 911 GT3 Cup, Техническое руководство

Результаты поиска

Содержание 2015 911 GT3 Cup

Отзывы:

Бренды по названию

Популярные бренды