Porsche 2015 911 GT3 Cup Скачать руководство пользователя страница 102

Страница: 102 / 321

Powertrain

Push the idler gear 3

gear (9) with idler gear bearing (10) on the guide sleeve (11)

(claws toward 4

gear) and thread onto the pinion shaft (Figure 2.9.7.14). Please

ensure in doing so that the oil holes of pinion shaft and guide sleeve are not directly

on top of each other (extensive oil supply).

Push on selector sleeve 3

gear (12) with the label facing outward (Figure

2.9.7.15)

Push the idler gear 4

gear (14) with idler gear bearing (13) (claws in the direction of

the 3

gear) onto the guide sleeve (Figure 2.9.7.15)

Push on fixed gear 4

gear (C) (installation direction toward fixed gear: label of fixed

gear (C) and label of idler gear (14) on the same side) (Figure 2.9.7.15)

2.9.7.12

2.9.7.13

2.9.7.14

2.9.7.15

Version: 16.12.2014

101

911 GT3 Cup (991)

MY 2015

Содержание 2015 911 GT3 Cup


































































































































































































































































































































Результаты поиска

Содержание 2015 911 GT3 Cup

Отзывы:

Бренды по названию

Популярные бренды

Porsche 2015 911 GT3 Cup, Техническое руководство

Результаты поиска

Содержание 2015 911 GT3 Cup

Отзывы:

Бренды по названию

Популярные бренды