Porsche 2015 911 GT3 Cup Скачать руководство пользователя страница 283

Страница: 283 / 321

Electrical System

Wheel lock lights

This function is provided to help the driver to prevent unnecessary tire wear caused

by locking front wheels.

A potential lock up of the front wheels are indicated by a flashing LED on the display.

If the front brake pressure is more than 10 bar (145 psi) and the speed of the left

front wheel is less than that of the left rear wheel by 20 kph (12 mph), the top left
warning light comes on (6.6.7.10).

If the front brake pressure is more than 10 bar (145 psi) and the speed of the right

front wheel is less than the speed of the right rear wheel by 20 kph (12 mph), the top

right warning light comes on (6.6.7.11).

Other indicator lights on the display

•

Left indicator:

the green LED (1) flashes.

•

Right indicator:

the green LED (3) flashes.

•

Warning lights:

the green LED´s (1) and (3) flash.

•

Driving lights:

the blue LED (4) lights, the LED (4) flashes in case

of a malfunction e.g. the right headlight is defective.

•

Engine control lamp:

the yellow LED (2) will appear in case of an error.

The information comes directly from the engine ECU

Map Page

The map is a bmp-file of 800x480 aspect ratio and is configured by Pi Toolset. If a

new bmp-file is loaded then this is displayed when the ICD is next power cycled. This

feature is to allow maps or other instructions to be displayed to the driver.

6.6.7.10

6.6.7.11

6.6.7.12

6.6.7.13

Version: 16.12.2014

282

911 GT3 Cup (991)

MY 2015

Содержание 2015 911 GT3 Cup


































































































































































































































































































































Результаты поиска

Содержание 2015 911 GT3 Cup

Отзывы:

Бренды по названию

Популярные бренды

Porsche 2015 911 GT3 Cup, Техническое руководство

Результаты поиска

Содержание 2015 911 GT3 Cup

Отзывы:

Бренды по названию

Популярные бренды