Porsche 2015 911 GT3 Cup Скачать руководство пользователя страница 14

Страница: 14 / 321

Engine

911 GT3 Cup (991)

MY 2015

Engine

1.1

General

The engine of the new 911 GT3 Cup (991) is based on the proven drive unit of the

street-legal 911 GT3 RS and has been redesigned especially for use in motor sports.

New features include the electronic accelerator and the accompanying throttle.

Furthermore, the Bosch Motronic MS4.6 controller has been used as engine control.

The engine has a dry sump lubrication system including an engine-mounted oil tank.

An oil-water heat exchanger integrated in the cooling circuit is used for oil cooling.

1.1.1

Version: 16.12.2014

Содержание 2015 911 GT3 Cup


































































































































































































































































































































Результаты поиска

Содержание 2015 911 GT3 Cup

Отзывы:

Бренды по названию

Популярные бренды

Porsche 2015 911 GT3 Cup, Техническое руководство

Результаты поиска

Содержание 2015 911 GT3 Cup

Отзывы:

Бренды по названию

Популярные бренды