Porsche 2015 911 GT3 Cup Скачать руководство пользователя страница 31

Страница: 31 / 321

Engine

911 GT3 Cup (991)

MY 2015

Alternately screw in the screw head of a commercially available slide hammer

puller in the holes and uniformly pull out the metal ring.

After removing the metal ring, the real seal remains in the crankcase.

Never pry it out!

Thoroughly remove the drilling shavings

Drill two more holes (arrows) using a 0.2 mm drill. Place these holes carefully as

possible in the corners (metal body) of the seal

A support ring that is provided to prevent a possible inclined position of the seal

is fitted behind the crankshaft seal. Therefore, drilling shvaings may occur,
which have to be thoroughly removed.

NOTE

1.6.5.2

Version: 16.12.2014

Содержание 2015 911 GT3 Cup


































































































































































































































































































































Результаты поиска

Содержание 2015 911 GT3 Cup

Отзывы:

Бренды по названию

Популярные бренды

Porsche 2015 911 GT3 Cup, Техническое руководство

Результаты поиска

Содержание 2015 911 GT3 Cup

Отзывы:

Бренды по названию

Популярные бренды