Porsche 2015 911 GT3 Cup Скачать руководство пользователя страница 222

Страница: 222 / 321

Bodywork

911 GT3 Cup (991)

MY 2015

Do not remove the beads on the carrier inside; they are part of the body!

Debur the bore holes on both sides of the body.

Creating a drilling template

Only a drilling template ensures exact positioning of the holes.

Make a drilling template from the defective strut mount. A body air saw is suitable for

sawing. Align the drilling template exactly and drill the 7 marked rivet holes.

Then deburr the holes.

Aligning the new part

Grind the gluing surfaces on the new part and on the body down to the bare metal

using P100 sandpaper and grease with acetone.

•

Apply evenly two-component glue on the new part

•

Curing time 2-3 hours at 60 °C (140 °F)

•

Install the new part with caution and fix it using fasteners.

•

Fit all rivets.

Pay attention to the correct rivet length!

4.15.2.6

4.15.2.7

4.15.2.8

Version: 16.12.2014

221

Содержание 2015 911 GT3 Cup


































































































































































































































































































































Результаты поиска

Содержание 2015 911 GT3 Cup

Отзывы:

Бренды по названию

Популярные бренды

Porsche 2015 911 GT3 Cup, Техническое руководство

Результаты поиска

Содержание 2015 911 GT3 Cup

Отзывы:

Бренды по названию

Популярные бренды