Porsche 2015 911 GT3 Cup Скачать руководство пользователя страница 292

Страница: 292 / 321

Maintenance

7.1

Engine

7.1.1

Oil level measurement using the dipstick

Conditions for the correct measurement:

•

The vehicle should be on a flat, even surface

•

Engine at operating temperature, oil temperature 80 °C (176 °F)

•

Idle speed

Follow the steps below for correct measuring:

•

Remove filler neck cap (7.1.1.1)

The dipstick (7.1.1.2) is located behind the cap in the

filler neck

•

Pull the dipstick out of the filler neck and wipe the oil off the dipstick using a
clean cloth

•

Introduce the dipstick again into the filler neck

•

Pull the dipstick again out of the oil reservoir and read the oil level

The difference between MIN and MAX is 1 liter (1.06

qt). (7.1.1.3) Fill in half liters (0.53 qt) of engine oil!

NOTE

7.1.1.1

7.1.1.2

7.1.1.3

Version: 16.12.2014

291

911 GT3 Cup (991)

MY 2015

Содержание 2015 911 GT3 Cup


































































































































































































































































































































Результаты поиска

Содержание 2015 911 GT3 Cup

Отзывы:

Бренды по названию

Популярные бренды

Porsche 2015 911 GT3 Cup, Техническое руководство

Результаты поиска

Содержание 2015 911 GT3 Cup

Отзывы:

Бренды по названию

Популярные бренды