Porsche 2015 911 GT3 Cup Скачать руководство пользователя страница 307

Страница: 307 / 321

Maintenance

7.4.2

Locking piece

The locking pieces are used as the locking mechanism for the wheel nuts. Make sure

that they can be moved freely. Grease the mechanism using “Optimol Paste”.

Consumables:

Porsche spare part no.: 000.043.004.00 Optimol Paste HAT

The locking mechanism may be removed from the hub for maintenance and cleaning.

Proceed as follows:

•

Press the locking pieces into the hub (blue arrow)

•

Press the locking pins into the hub using a thin object (yellow arrow)

•

Pull the mechanism approx. 5 mm (0.2”) out of the hub

Before completely removing the unit, put a stable bag
or a strong cloth around the hub, providing protection

against flying parts!

•

Put the protection over the hub

•

Completely remove the mechanism from the hub

Risk of injury when removing the unit due to the strong

spring preload.

NOTE

WARNING

7.4.2.1

Version: 16.12.2014

306

911 GT3 Cup (991)

MY 2015

Содержание 2015 911 GT3 Cup


































































































































































































































































































































Результаты поиска

Содержание 2015 911 GT3 Cup

Отзывы:

Бренды по названию

Популярные бренды

Porsche 2015 911 GT3 Cup, Техническое руководство

Результаты поиска

Содержание 2015 911 GT3 Cup

Отзывы:

Бренды по названию

Популярные бренды