Porsche 2015 911 GT3 Cup Скачать руководство пользователя страница 296

Страница: 296 / 321

Maintenance

Filling the cooling system

•

Disconnect the quick coupling in the engine compartment and connect the
open ends to the two couplings of the filling device

•

Switch on the pump; the system is being filled

•

The device should be turned on for ten minutes to ensure proper filling and
venting

•

Allow the engine to warm up (80 °C / 176 °F) and, if required, fill the
container up to the maximum level using the connected filling device

•

The compensating tank cover must be closed during the entire procedure

Never open the cover of the coolant compensating

tank after reaching the operating temperature. The

system pressure would escape and will not be built up

again as the operating temperature has already been

reached. This pressure is, however, required to
increase the boiling point of the cooling water.

A special filling device should be used for filling the water system (7.1.6.2). This

device is distributed by Sobek. The filling device includes an electric pump that

pumps the cooling water from a tank into the system.

NOTE

7.1.6.2

SOBEK Motorsporttechnik GmbH & Co.KG

Industriestraße 8

68542 Heddesheim

Tel.: +49 (0)62 03-40 43 90 0

Fax: +49 (0)62 03-40 43 91 8

E-Mail: [email protected]

Version: 16.12.2014

295

911 GT3 Cup (991)

MY 2015

Содержание 2015 911 GT3 Cup


































































































































































































































































































































Результаты поиска

Содержание 2015 911 GT3 Cup

Отзывы:

Бренды по названию

Популярные бренды

Porsche 2015 911 GT3 Cup, Техническое руководство

Результаты поиска

Содержание 2015 911 GT3 Cup

Отзывы:

Бренды по названию

Популярные бренды