Panasonic SL-VGU1-C Скачать руководство пользователя страница 45

Страница: 45 / 96

Chapter 2

Memory Map

8. RX (n) bit 8 to B: Number of I/O control points 0 to 3

The number of I/O control points will be stored.

Storage place

Number of I/O control points

512 480 448 416 384 352 320 288 256 224 192 160 128 96

RX (n) bit 8

RX (n) bit 9

RX (n) bit A

RX (n) bit B

9. RX (n) bit E: Completion of transmission frame check

At the completion of transmission frame check, this bit will be turned on (will be set to ‘1’).

If RY (n) bit E (transmission frame check request) is turned off (set to ‘0’), this signal will be turned off (will be

set to ‘0’).

10. RX (n) bit F: BUSY

At power-on or during system setting operation, the system is not ready for transmission. In this case, this bit

will be turned on (will be set to ‘1’).

Note: In the

S-LINK V

User’s Manual, this signal is referred to as the ‘READY output.’

11. RX (n+1) bit 0 to 8: Number of nodes bit 0 to 8

●

If RX (n+2) bit 0 (completion of connection information change) is turned off (set to ‘0’)

This signal indicates the number of nodes (

S-LINK V

I/O units) recognized by the

SL-VGU1-C

Numbers 0000 to 0100H (0 to 256) can be input.

●

If RX (n+2) bit 0 (completion of connection information change) is turned on (set to ‘1’)

This signal indicates the number of nodes (

S-LINK V

I/O units) connected to the

S-LINK V

system, those

error 3, 4, or 5 is detected.

Numbers 0000 to 0100H (0 to 256) can be input.

Note: If only 1 station (I/O points: 64 points or less each) is used, this signal (number of nodes) will not be assigned to the RX (n+1). In this

case, the completion of initial data setting, error status, remote READY status signals will be assigned to the RX (n+1).

12. RX (n+2) bit 0: Completion of connection information change

If RY (n+2) bit 0 (connection information change request) is turned on (set to ‘1’), this bit will be turned on

(will be set to ‘1’), and if RY (n+2) bit 0 (connection information change request) is turned off (set to ‘0’), this

bit will be turned off (will be set to ‘0’).

Check whether the data of RY (n+2) bit 0 (connection information change request) corresponds with the data

of RX (n+2) bit 0 (completion of connection information change,) and then read out RX (n+1) bit 0 to 8 (num-

ber of nodes bit 0 to 8), RX (n+3) (address information A), or RX (n+4) (address information B) to prevent an

error in reading information.

13. RX (n+2) bit 8 to B: Completion of address information change bit 0 to 3

The same data as RY (n+2) bit 8 to B (address information change request bit 0 to 3) will be stored.

Check whether the data of RY (n+2) bit 8 to B (address information change request bit 0 to 3) corresponds

with the data of RX (n+2) bit 8 to B (completion of address information change bit 0 to 3), and then read out

RX (n+3) (address information A), or RX (n+4) (address information B) to prevent an error in reading infor-

mation.

Содержание SL-VGU1-C

































































































Результаты поиска

Содержание SL-VGU1-C

Отзывы:

Похожие инструкции для SL-VGU1-C

Бренды по названию

Популярные бренды

Panasonic SL-VGU1-C, Руководство пользователя

Результаты поиска

Содержание SL-VGU1-C

Отзывы:

Похожие инструкции для SL-VGU1-C

Бренды по названию

Популярные бренды