Panasonic SL-VGU1-C Скачать руководство пользователя страница 23

Страница: 23 / 96

Chapter 2

Specifications

List of Specifications

Designation

S-LINK V

gateway controller for CC-Link

Model No.

SL-VGU1-C

Supply voltage

24V DC

+10

Current consumption

300mA or less (excluding error output load and power supply for driving I/O units) (Note 2)

Allowable through current

7A (Note 3)

S-LINK V

system side

Transmission method

Bidirectional time-divided multiple transmission method

Synchronization method

Bit synchronization method, frame synchronization method

Transmission procedure

S-LINK V

protocol

Transmission speed

A mode: 110kbps, B mode: 27.5kbps, C mode: 6.9kbps

Refresh time

A mode: 0.29 to 10.32ms, B mode: 1.18 to 41.29ms, C mode: 4.70 to 165.15ms

I/O points

Buffer memory assignment pattern 1: 128 inputs max., 128 outputs max. (Note 4)

Buffer memory assignment pattern 2: 256 inputs max., 256 outputs max. (Note 5)

Connected node No.

256 nodes max.

Transmission distance

A mode: 50m max., B mode: 200m max., C mode: 800m max.

Total wiring length

A mode: 100m or less, B mode: 400m or less, C mode: 1,600m or less

Transmission cable

Exclusive 4-core flat cable (0.5mm

) or

Conductor cross-section area 0.3 to 2.0mm

4-core VCTF cable (without shield) (Note 6)

I/O combination

I/O settable in units of 32 Nos.

Indicators

Transmission

Green LED (Blinks during transmission.)

Error

Red LED (Lights up when an error occurs. Blinks when the cause of the error is eliminated. Turns off when

normal operation is performed.)

Hexadecimal

Orange LED (Lights up when the address display is in the hexadecimal number display mode.)

Address display

3 digits red LED (Displays the number of connected nodes, recognized address, error address, etc.)

Error output

NPN open-collector transistor

•

Maximum sink current: 100mA (without short-circuit protection)

•

Applied voltage: 30V DC or less (between error output and 0V)

•

Residual voltage: 1.5V or less (at 100mA sink current)

CC-Link side

Compatible network

CC-Link Ver1.10

Occupied station No.

1 to 4 stations (varies with

S-LINK V

I/O control points.)

Transmission speed

10Mbps

5Mbps

2.5Mbps

625kbps

156kbps

Total extension

100m

160m

400m

900m

1,200m

Transmission cable

Specified cable (shielded twisted pair cable)

Operation indicators

L RUN (Green), L ERROR (Red), RD (Green), SD (Green)

Remote unit classification

Remote device unit

Environmental resistance

Ambient temperature

0 to +55ºC (No dew condensation), Storage: -20 to +70ºC

Ambient humidity

10 to 90% RH, Storage: 10 to 90% RH

Noise immunity

Power line: 500Vp, 10ms cycle, 1µs pulse width

Common: 1,000Vp, 10ms cycle, 1µs pulse width (with noise simulator)

Voltage withstandability

1,000V AC for one min. between all terminals connected together and enclosure

Insulation resistance

20MΩ, or more, with 500V DC megger between all terminals connected together and enclosure

Vibration resistance

10 to 150Hz frequency, 0.75mm amplitude or acceleration of 5G in X, Y and Z directions for two hours each

Shock resistance

294m/s

acceleration (30G approx.) in X, Y and Z directions for three times each

Grounding method

F.G. terminal: C-connection, Enclosure: Floating

Mounting

Mounted on DIN rail or mounting M4 screw (length: 12mm or less)

Material

Enclosure: ABS

Weight

200g approx.

Terminal blocks

S-LINK V

terminal block connector (8-pole): 2ESDVM-08P (manufactured by Dinkle Enterprise Co., Ltd.)

CC-Link terminal block connector (8-pole): EC381VM-08P (manufactured by Dinkle Enterprise Co., Ltd.)

Notes: 1) Mainly the

S-LINK V

sysytem side specifications are given above. The CC-Link side conforms to CC-Link specifications. Please

confirm the details from CC-Link Partner Association.

2) The current consumption value shown here is the total of the maximum current (D-G line only) supplied to the

S-LINK V

I/O units

and the current consumption of the

S-LINK V

gateway controller.

3) This product is not equipped with any short-circuit protective function. For this reason, select a power supply unit having short-

circuit protective function (fuse, etc.).

4) In case of buffer memory assignment pattern 1, 112 channels are assigned to remote I/O (RX / RY) and the balance 16 channels

are assigned to remote register (RWrm / RWwm).

5) If buffer memory assignment pattern 2 is used, all the points will be assigned to the remote registers (RWrm /RWwm).

6) The VCTF cable is the vinyl cabtyre cable that conforms to the requirements of JIS C 3306 ‘Polyvinyl chloride insulated flexible

cords.’

Содержание SL-VGU1-C

































































































Результаты поиска

Содержание SL-VGU1-C

Отзывы:

Похожие инструкции для SL-VGU1-C

Бренды по названию

Популярные бренды

Panasonic SL-VGU1-C, Руководство пользователя

Результаты поиска

Содержание SL-VGU1-C

Отзывы:

Похожие инструкции для SL-VGU1-C

Бренды по названию

Популярные бренды