Panasonic SL-VGU1-C Скачать руководство пользователя страница 10

Страница: 10 / 96

Before Using This System

Introduction For Use

Wiring

Observe the following items to distribute cables:

●

Make sure to carry out the installation and the wiring in the power supply off condition.

● Be sure to use the specified

S-LINK V

cables, CC-Link cables, or DeviceNet cables.

●

To protect the cables from noise, shorten the cable length as far as possible.

●

Do not run the wires together with high-voltage lines or power lines or put them in the same raceway. This

can cause malfunction due to induction.

●

Do not completely fold down any cables.

●

Do not pull any cables with a strong force.

●

Do not apply any weight to any cable.

●

Do not touch a cable to any other system cables. This is because signals of different systems may interfere

with each other.

●

Take care that wrong wiring damage the sensor.

Others

● Apply the specified torque to tighten the terminal screws.

●

Check the connectors for looseness.

●

Do not disassemble or modify this product.

●

Before touching this product, be sure to discharge the static electricity from your body. This is because

static electricity on your body may damage the product.

●

Design the system so that the system protective devices and safety circuits are outside the system.

Instructions for Disposal

●

Request a waste disposal company to dispose of this product.

Содержание SL-VGU1-C

































































































Результаты поиска

Содержание SL-VGU1-C

Отзывы:

Похожие инструкции для SL-VGU1-C

Бренды по названию

Популярные бренды

Panasonic SL-VGU1-C, Руководство пользователя

Результаты поиска

Содержание SL-VGU1-C

Отзывы:

Похожие инструкции для SL-VGU1-C

Бренды по названию

Популярные бренды