Panasonic SL-VGU1-C Скачать руководство пользователя страница 61

Страница: 61 / 96

Chapter 2

Error Indication

If an error occurs on the system, the

SL-VGU1-C

will output the error signal, and the error indicator and the ad-

dress display of the controller will inform the error.

Error Indication on S-LINK V System Side

Error No.

Cause of error

Transmission state during error

Error 0

•

Fault in system (controller)

Transmission stopped

Error 1

•

Short-circuit b24V and D

Transmission stopped.

Restarted automatically 5 sec. after cause of error is

rectified.

Error 2

•

Short-circuit between D and G

Error 3

•

Fault or disconnection of recognized I/O unit

Transmission continued

Error 4

•

Addition of unrecognized unit

Error 5

•

Output short-circuit of output unit

•

Drive power supply of I/O device switched off

Error 6

•

System setting not done correctly.

Automatically restored when system setting is cor-

rectly done.

Note: If two or more errors are detected at the same time, errors 1 and 2 will be given priority in indication.

Error Indication on CC-Link Side

Indicator

Cause of error

L RUN

(Green)

Lights up

•

When data sent from the master station is received properly.

Turns off

•

When a data receiving error, transmission error (CRC error), or overtime is detected.

L ERROR

(Red)

Lights up

•

When a transmission error (CRC error) is detected.

•

When a station number setting error or transmission speed (baud rate) setting error is detected.

Blinks

•

When the set station number or transmission speed is changed during operation.

Turns off

•

When a transmission error (CRC error) or overtime is detected.

RD (Green)

•

Lights up depending on the received data.

SD (Green)

•

Lights up depending on the sent data.

Содержание SL-VGU1-C

































































































Результаты поиска

Содержание SL-VGU1-C

Отзывы:

Похожие инструкции для SL-VGU1-C

Бренды по названию

Популярные бренды

Panasonic SL-VGU1-C, Руководство пользователя

Результаты поиска

Содержание SL-VGU1-C

Отзывы:

Похожие инструкции для SL-VGU1-C

Бренды по названию

Популярные бренды