Panasonic SL-VGU1-C Скачать руководство пользователя страница 47

Страница: 47 / 96

Chapter 2

Memory Map

17. RY (n+2) bit 0: Connection information change request

Use the connection information change request to change the data that will be stored in RX (n+1) bit 0 to 8

(number of nodes bit 0 to 8), RX (n+3) (address information A), or RX (n+4) (address information B).

●

If RY (n+2) bit 0 (connection information change request) is turned off (set to ‘0’)

Number of nodes (

S-LINK V

I/O units) recognized by the

SL-VGU1-C

will be stored in RX (n+1) bit 0 to

(number of nodes bit 0 to 8), and the address information will be stored in RX (n+3) (address information

A), or RX (n+4) (address information B).

●

If RY (n+2) bit 0 (connection information change request) is turned on (set to ‘1’)

Number of nodes (

S-LINK V

I/O units) connected to the

S-LINK V

system, those error 3, 4, or 5 is de-

tected will be stored in RX (n+1) bit 0 to 8 (number of nodes bit 0 to 8), and the address information will be

stored in RX (n+3) (address information A), or RX (n+4) (address information B).

18. RY (n+2) bit 8 to B: Address information change request bit 0 to 3

●

Address that corresponds to the data stored in RY (n

＋

2) bit 8 to B (address information change request

bit 0 to 3) will be stored in RX (n+3) (address information A), or RX (n+4) (address information B).

Bit corresponds to the address will be turned on (set to ‘1’).

Example: If number of I/O control points = 512, inputs = 0 to 127, outputs = 128 to 255, inputs = 256 to 383

outputs = 384 to 511

S-LINK V

address

Addresses 0 to 127

Inputs

Remote input (RX)

Remote output (RY)

RX (n

＋

Number of nodes

bit 0 to 8

RX (n+3), RX (n+4)

Address information

A, B

RX (n+5), RX (n+6)

Not used

RX (n)

Errors 0 to 6, Error status
Number of I/O control points 0 to 3
Completion of transmisson frame check

BUSY

RY (n+1)
Not used

RY (n+3) to RY (n+6)

Not used

Addresses 128 to 255

Outputs

Addresses 256 to 383

Inputs

Addresses 384 to 511

Outputs

Buffer memory

Remote register (RWrm)

RWrm (m) to

RWrm (m+7)

IN 0 to 127

RWrm (m+8) to

RWrm (m+F)

IN 128 to 255

Remote register (RWwm)

RWwm (m) to

RWwm (m+7)

OUT 0 to 127

RWwm (m+8) to

RWwm (m+F)

OUT 128 to 255

RX (n+7)

Completion of initial data setting

Error status

Remote READY status

RY (n

Initial data setting request

RY (n+2)

Connection information

change request

Address information

change request

RY (n)

Error cancel

Transmission frame
check request

RX (n+2)

Completion of connection

information change

Completion of address

information change

Notes: 1) If only 1 station (I/O points: 64 points or less each) is used for buffer memory assignment pattern 2, the number of nodes signal

will not be assigned to the RX (n+1). In this case, the completion of initial data setting, error status, remote READY status signals

will be assigned to the RX (n+1).

2) The addresses of ‘IN 0 to 255’ and ‘OUT 0 to 255’ shown above differ from these addresses on the

S-LINK V

system side.

(However, in the all-point input status or all-point output status, the above addresses will be equal to the

S-LINK V

addresses.)

Содержание SL-VGU1-C

































































































Результаты поиска

Содержание SL-VGU1-C

Отзывы:

Похожие инструкции для SL-VGU1-C

Бренды по названию

Популярные бренды

Panasonic SL-VGU1-C, Руководство пользователя

Результаты поиска

Содержание SL-VGU1-C

Отзывы:

Похожие инструкции для SL-VGU1-C

Бренды по названию

Популярные бренды