Panasonic SL-VGU1-C Скачать руководство пользователя страница 44

Страница: 44 / 96

Chapter 2

Memory Map

●

If buffer memory assignment pattern 2 is used:

1. RWrm (m) to RWrm (m+F), RWwm (m) to RWwm (m+F): S-LINK V I/O data

These are I/O data signals of the

S-LINK V

system.

2. RX (n+o) bit 9: Completion of initial data setting

This signal will be turned on if the RY (n+o) bit 9 (initial data setting request) is turned on.

If the RY (n+o) bit 9 (initial data setting request) is turned off, this signal will be also turned off.

Note: The value ‘o’ depends on the number of occupied CC-Link stations. [1 station = 1, 2 stations = 3, 3 stations = 5, 4 stations = 7]

3. RX (n+o) bit A: Error status

This signal will be turned on if one of errors 0 to 6 is detected on the

S-LINK V

system.

Note: The value ‘o’ depends on the number of occupied CC-Link stations. [1 station = 1, 2 stations = 3, 3 stations = 5, 4 stations = 7]

4. RX (n+o) bit B: Remote READY status

If the power is turned on, if the system enters the system setting mode, or if the

SL-VGU1-C

enters the

READY status (exits from the BUSY status), this signal will be turned on.

If the RY (n+o) bit 9 (initial data setting request) is turned off, this signal will be also turned off.

Note: The value ‘o’ depends on the number of occupied CC-Link stations. [1 station = 1, 2 stations = 3, 3 stations = 5, 4 stations = 7]

5. RY (n+o) bit 9: Initial data setting request

The

SL-VGU1-C

will not use this signal to set or modify the initial data.

Note: The value ‘o’ depends on the number of occupied CC-Link stations. [1 station = 1, 2 stations = 3, 3 stations = 5, 4 stations = 7]

6. RX (n) bit 0 to 6: Errors 0 to 6

Error 0:

The system (controller) has a problem.

Note: Error 0 will stop the transmission.

Error 1:

If error 1 (short-circuit b24V and D) is detected on the main line of the

S-LINK V

system, this bit

will be turned on (will be set to ‘1’).

Note: Error 1 will stop the transmission. If the cause of the error is eliminated, the system will be automatically reset 5 seconds later.

Error 2:

If error 2 (short-circuit between D and G) is detected on the main line of the

S-LINK V

system, this bit will

be turned on (will be set to ‘1’).

Note: Error 2 will stop the transmission. If the cause of the error is eliminated, the system will be automatically reset 5 seconds later.

Error 3:

If an I/O unit has a problem or disconnected, this bit will be turned on (will be set to ‘1’).

Note: Error 3 will not stop the transmission.

Error 4:

If an unrecognized unit is added, this bit will be turned on (will be set to ‘1’).

Note: Error 4 will not stop the transmission.

Error 5:

If an output terminal of an output unit is shorted, or if I/O device driving power is stopped, this bit will be

turned on (will be set to ‘1’).

Note: Error 5 will not stop the transmission.

Error 6:

If system setting operation is not performed properly, this bit will be turned on (will be set to ‘1’).

Note: If system setting operation is performed properly, transmission will be started.

7. RX (n) bit 7: Error status

If an error is detected, this bit will be turned on (will be set to ‘1’). If the cause of the error is eliminated, this bit

will be turned off (will be set to ‘0’).

Содержание SL-VGU1-C

































































































Результаты поиска

Содержание SL-VGU1-C

Отзывы:

Похожие инструкции для SL-VGU1-C

Бренды по названию

Популярные бренды

Panasonic SL-VGU1-C, Руководство пользователя

Результаты поиска

Содержание SL-VGU1-C

Отзывы:

Похожие инструкции для SL-VGU1-C

Бренды по названию

Популярные бренды