Panasonic SL-VGU1-C Скачать руководство пользователя страница 84

Страница: 84 / 96

Chapter 3

Starting

Mode setting

Mode setting

Operation

Description / Function

Indication

Setting of transmission mode

In the CONFIG mode, turn on

the power.

Press ENTER key.

Displays the current transmission mode.

Blinks the displayed current transmission mode.

Example

Press key or key.

Selects the transmission mode from the three types (A

mode, B mode and C mode), and then displays the se-

lected mode.

If A mode is

selected:

If B mode is

selected:

If C mode is

selected:

Press ENTER key.

Determines the transmission mode.

Example

Setting of display to decimal / hexadecimal number display

Press key.

Displays the code of the decimal / hexadecimal number

setting.

Example

Press ENTER key.

Blinks the displayed code of the decimal / hexadecimal

number setting.

Decimal number

display

Press key or key.

Selects either the decimal or hexadecimal number dis-

play.

Hexadecimal

number display

Press ENTER key.

Determines the display.

If the hexadecimal number display is selected, the

code 'd 16' will appear.

Example

Presetting

Press key.

Displays the preset value.

Example

Press ENTER key.

Blinks the displayed preset value.

If the preset value

is '0':

Press key or key.

Selects a value to be preset.

If the preset value

is '8':

Press ENTER key.

Determines the preset value.

(If the preset value is '0,' nothing will be changed.)

Example

Setting of number of I/O control points

Press key.

Displays the number of I/O control points.

Example

Press ENTER key.

Blinks the displayed number of I/O control points.

If 512 points is

selected:

Press key or key.

Selects the number of I/O control points in the range of

32 to 512 points. Selection is possible in increments /

decrements of 32 points.

If 32 points is

selected:

Press ENTER key.

Determines the number of I/O control points.

Example

Содержание SL-VGU1-C

































































































Результаты поиска

Содержание SL-VGU1-C

Отзывы:

Похожие инструкции для SL-VGU1-C

Бренды по названию

Популярные бренды

Panasonic SL-VGU1-C, Руководство пользователя

Результаты поиска

Содержание SL-VGU1-C

Отзывы:

Похожие инструкции для SL-VGU1-C

Бренды по названию

Популярные бренды