Panasonic SL-VGU1-C Скачать руководство пользователя страница 41

Страница: 41 / 96

Chapter 2

Memory Map

8. RWrm (m+1) bit 8 to B: Number of I/O control points 0 to 3

The number of I/O control points will be stored.

Storage place

Number of I/O control points

512 480 448 416 384 352 320 288 256 224 192 160 128 96

RWrm (m+1) bit 8

RWrm (m+1) bit 9

RWrm (m+1) bit A

RWrm (m+1) bit B

9. RWrm (m+1) bit E: Completion of transmission frame check

At the completion of transmission frame check, this bit will be turned on (will be set to ‘1’).

If RWwm (m+1) bit E (transmission frame check request) is turned off (set to ‘0’), this signal will be turned off

(will be set to ‘0’).

10. RWrm (m+1) bit F: BUSY

At power-on or during system setting operation, the system is not ready for transmission. In this case, this bit

will be turned on (will be set to ‘1’).

Note: In the

S-LINK V

User’s Manual, this signal is referred to as the ‘READY output.’

11. RWrm (m+2) bit 0 to 8: Number of nodes bit 0 to 8

●

If RWrm (m+3) bit 0 (completion of connection information change) is turned off (set to ‘0’)

This signal indicates the number of nodes (

S-LINK V

I/O units) recognized by the

SL-VGU1-C

Numbers 0000 to 0100H (0 to 256) can be input.

●

If RWrm (m+3) bit 0 (completion of connection information change) is turned on (set to ‘1’)

This signal indicates the number of nodes (

S-LINK V

I/O units) connected to the

S-LINK V

system, those

error 3, 4, or 5 is detected.

Numbers 0000 to 0100H (0 to 256) can be input.

12. RWrm (m+3) bit 0: Completion of connection information change

If RWwm (m+3) bit 0 (connection information change request) is turned on (set to ‘1’), this bit will be turned

on (will be set to ‘1’), and if RWwm (m+3) bit 0 (connection information change request) is turned off (set to

‘0’), this bit will be turned off (will be set to ‘0’).

Check whether the data of RWwm (m+3) bit 0 (connection information change request) corresponds with the

data of RWrm (m+3) bit 0 (completion of connection information change), and then read out RWrm (m+2) bit

0 to 8 (number of nodes bit 0 to 8), and RWrm (m+4) to RWrm (m+F) (address information 0 to 191 / 192 to

255) to prevent an error in reading information.

13. RWrm (m+3) bit 8: Completion of address information change

If RWwm (m+3) bit 8 (address information change request) is turned on (set to ‘1’), this bit will be turned on

(will be set to ‘1’), and if RWwm (m+3) bit 8 (address information change request) is turned off (set to ‘0’),

this bit will be turned off (will be set to ‘0’).

Check whether the data of RWwm (m+3) bit 8 (address information change request) corresponds with the

data of RWrm (m+3) bit 8 (completion of address information change,) and then read out RWrm (m+C) to

RWrm (m+F) (address information 128 to 191 / 192 to 255) (refer to page 32).

14. RWrm (m+4) to RWrm (m+F): Address information 0 to 191 / 192 to 255

●

If RWrm (m+3) bit 0 (completion of connection information change) is turned off (set to ‘0’)

Address of

S-LINK V

I/O units recognized by the

SL-VGU1-C

will be stored.

Bit corresponds to the address will be turned on (will be set to ‘1’).

●

If RWrm (m+3) bit 0 (completion of connection information change) is turned on (set to ‘1’)

Address of

S-LINK V

I/O units connected to the

S-LINK V

system, those error 3, 4, or 5 is detected will be

stored.

Bit corresponds to the address will be turned on (will be set to ‘1’).

●

If RWrm (m+3) bit 8 (completion of address information change) is turned off (set to ‘0’)

Information of address 128 to 191 of

S-LINK V

I/O units will be stored in RWrm (m+C) to RWrm (m+F)

(address information 128 to 191 / 192 to 255).

Bit corresponds to the address will be turned on (set to ‘1’).

●

If RWrm (m+3) bit 8 (completion of address information change) is turned on (set to ‘1’)

Information of address 192 to 255 of

S-LINK V

I/O units will be stored in RWrm (m+C) to RWrm (m+F)

(address information 128 to 191 / 192 to 255).

Bit corresponds to the address will be turned on (set to ‘1’).

Содержание SL-VGU1-C

































































































Результаты поиска

Содержание SL-VGU1-C

Отзывы:

Похожие инструкции для SL-VGU1-C

Бренды по названию

Популярные бренды

Panasonic SL-VGU1-C, Руководство пользователя

Результаты поиска

Содержание SL-VGU1-C

Отзывы:

Похожие инструкции для SL-VGU1-C

Бренды по названию

Популярные бренды