Panasonic SL-VGU1-C Скачать руководство пользователя страница 79

Страница: 79 / 96

Chapter 3

Memory Map

Assignment Items

1. S-LINK V I/O data

These are I/O data signals of the

S-LINK V

system.

2. Errors 0 to 6

Error 0:

The system (controller) has a problem.

Note: Error 0 will stop the transmission.

Error 1:

If error 1 (short-circuit b24V and D) is detected on the main line of the

S-LINK V

system, this bit

will be turned on (will be set to ‘1’).

Note: Error 1 will stop the transmission. If the cause of the error is eliminated, the system will be automatically reset 5 seconds later.

Error 2:

If error 2 (short-circuit between D and G) is detected on the main line of the

S-LINK V

system, this bit will

be turned on (will be set to ‘1’).

Note: Error 2 will stop the transmission. If the cause of the error is eliminated, the system will be automatically reset 5 seconds later.

Error 3:

If an I/O unit has a problem or disconnected, this bit will be turned on (will be set to ‘1’).

Note: Error 3 will not stop the transmission.

Error 4:

If an unrecognized unit is added, this bit will be turned on (will be set to ‘1’).

Note: Error 4 will not stop the transmission.

Error 5:

If an output terminal of an output unit is shorted, or if I/O device driving power is stopped, this bit will be

turned on (will be set to ‘1’).

Note: Error 5 will not stop the transmission.

Error 6:

If system setting operation is not performed properly, this bit will be turned on (will be set to ‘1’).

Note: If system setting operation is performed properly, transmission will be started.

3. Error status

If an error is detected, this bit will be turned on (will be set to ‘1’). If the cause of the error is eliminated, this bit

will be turned off (will be set to ‘0’).

4. Number of I/O control points 0 to 3

The number of I/O control points will be stored.

Storage place

Number of I/O control points

512 480 448 416 384 352 320 288 256 224 192 160 128 96

No. of I/O control points 0 1

No. of I/O control points 1 1

No. of I/O control points 2 1

No. of I/O control points 3 1

5. Completion of transmission frame check

At the completion of transmission frame check, this bit will be turned on (will be set to ‘1’).

If transmission frame check request is turned off (set to ‘0’), this signal will be turned off (will be set to ‘0’).

6. BUSY

At power-on or during system setting operation, the system is not ready for transmission. In this case, this bit

will be turned on (will be set to ‘1’).

Note: In the

S-LINK V

User’s Manual, this signal is referred to as the ‘READY output.’

Содержание SL-VGU1-C

































































































Результаты поиска

Содержание SL-VGU1-C

Отзывы:

Похожие инструкции для SL-VGU1-C

Бренды по названию

Популярные бренды

Panasonic SL-VGU1-C, Руководство пользователя

Результаты поиска

Содержание SL-VGU1-C

Отзывы:

Похожие инструкции для SL-VGU1-C

Бренды по названию

Популярные бренды