Panasonic SL-VGU1-C Скачать руководство пользователя страница 86

Страница: 86 / 96

Chapter 3

Starting

Mode setting

Operation

Description / Function

Indication

Setting of error 1 output operation

Press key.

Displays the error 1 output operation.

Example

Press ENTER key.

Blinks the displayed error 1 output operation.

Error output 1

Press key or key.

Selects the external output type for the detected error

from the following two types:

: Outputs the error signal from error output 1 of the controller.

: Will not output any error signal.

No error output

Press ENTER key.

Determines the error 1 output operation.

Example

Setting of errors 2 to 5 output

operation

Follow the same operation

procedure as error 1.

Switching in the order of

errors 2, 3, 4 and 5

Same as error 1

Default setting

Press key.

Displays the code of the default setting.

Press ENTER key.

(for 3 seconds)

Displays the indicator check pattern, and sets the default

values.
Sequentially displays all the setting items of the CONFIG

mode, and sets these items to the initial values (default

values).

Clears the addresses of all the units specified in the sys

tem setting.

End

System setting

Press key.

Displays the code of the system setting.

Enters the system setting (blinks).

Example

Press and hold ENTER key

until the displayed code

blinks (for 3 seconds).

Blinks the number of connected nodes (I/O units).

If 4 I/O units are

connected:

End

SL-VGU1-D setting default values (values set in our factory before delivery)

Setting of transmission mode

Setting of display to decimal /

hexadecimal number display

Presetting

Status assignment

Setting of number of

I/O control points

I/O setting 0

I/O setting 1

I/O setting 2

I/O setting 3

Output hold / clear

Setting of error 2

output operation

Setting of error 1

output operation

Setting of error 3

output operation
Setting of error 4

output operation
Setting of error 5

output operation

Содержание SL-VGU1-C

































































































Результаты поиска

Содержание SL-VGU1-C

Отзывы:

Похожие инструкции для SL-VGU1-C

Бренды по названию

Популярные бренды

Panasonic SL-VGU1-C, Руководство пользователя

Результаты поиска

Содержание SL-VGU1-C

Отзывы:

Похожие инструкции для SL-VGU1-C

Бренды по названию

Популярные бренды