Panasonic SL-VGU1-C Скачать руководство пользователя страница 9

Страница: 9 / 96

Before Using This System

Introduction For Use

Use with conventional products

The

S-LINK V

system cannot be used together with the conventional

S-LINK

system. Use with a conventional

system may cause abnormal operation or damage.

However, if these systems are used as the child stations of the open network (CC-Link, DeviceNet), 2 systems

can be used together on the same network as 2 series of systems.

S-LINK V

gateway

controller

S-LINK V

unit

S-LINK

unit

S-LINK V

gateway

controller

S-LINK V

unit

S-LINK V

unit

S-LINK

gateway

controller

S-LINK

unit

S-LINK

unit

Not good

Good

Instructions for Installation

●

Before starting the following works, be sure to turn off the power of the PLC (programmable logic

controller), personal computer main body,

S-LINK V

units, and also turn off the power supply unit

of the I/O device.

•

Machine assembly (installation)

•

Removal or reinstallation of a

S-LINK V

gateway controller or connection of I/O device

•

Cable connection

•

Address setting / change

●

Before touching this product, remove any electrostatic charge that may be present on your body.

There is a danger of this product getting damaged due to the electrostatic charge.

CAUTION

Power supply unit

Observe the following items to use a power supply unit:

●

This product has no short-circuit protective function. For this reason, be sure to select a power supply unit

having a short-circuit protective function (fuse, etc.).

●

If power is supplied from a commercial switching regulator, ensure that the frame ground (F.G.) terminal of

the power supply is connected to an actual ground.

●

Do not use during the initial transient time after the power supply is switched on. Further, transmission is

not possible when the system is in BUSY state (during switching on the power supply or system setting).

●

Make sure to use an isolation transformer for the DC power supply. If an auto-transformer (single winding

transformer) is used, this product or the power supply may get damaged.

●

In case a surge is generated in the used power supply, connect a surge absorber to the power supply and

absorb the surge.

Содержание SL-VGU1-C

































































































Результаты поиска

Содержание SL-VGU1-C

Отзывы:

Похожие инструкции для SL-VGU1-C

Бренды по названию

Популярные бренды

Panasonic SL-VGU1-C, Руководство пользователя

Результаты поиска

Содержание SL-VGU1-C

Отзывы:

Похожие инструкции для SL-VGU1-C

Бренды по названию

Популярные бренды