Panasonic fp2/fp2sh Скачать руководство пользователя страница 214 | Manualshive

Страница: 214 / 374

background image

FP2/FP2SH

IC Memory Card

7

−

4

7.1

Using the IC Memory Card

7.1.2

Using the IC Memory Card

The IC memory card is available as an optional memory for the FP2

−

C2P/FP2

−

C3P.

(It cannot be used with the FP2

−

C2.)

IC memory cards can be used for two types of applications: saving programs and ex-

panding the data memory area. Also, a single IC memory card can be used in the

following three ways:
Only for saving programs
Only for expanding the data memory area
For both saving programs and expanding the data memory area

Using the Card to Save Programs

Sequence programs can be written to IC memory cards and saved on them. The IC

memory card with the program written to it is then used as a program memory.
If the FPWIN GR or a similar tool is used to change the file name to “Autoexec.spg”, as

an auto run file, and the file is copied or the program is transferred, and if the DIP

switches on the CPU are set so that SW2 and SW4 are both on, the program can be

automatically transferred to the RAM at the same time that the power supply is turned

on.

If the

F14 (PRGRD)

instruction is executed in the RUN mode, a program can be substi-

tuted for another program in any desired file.

If an SRAM type of IC memory card is being used, the “ROM & RAM service” in the

FPWIN GR can be used to copy the contents of the RAM in the CPU to the IC memory

card.
If the card is being used as a program memory, there are four ways to read programs

from the card, described below:

Programs can be automatically read when the power supply is turned on.

Programs can be read using the “ROM & RAM service” menu on the FPWIN GR.

Programs can be read using the “Upload Program from IC Card...” menu on the FPWIN

GR.

The

F14 (PRGRD)

instruction of the sequence program can be used to read programs.

«
...
212
213
214
215
216
...
»

Содержание fp2/fp2sh























































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для fp2/fp2sh

Бренд: Banner Страницы: 15

Бренд: bar Страницы: 2

IntelliZone2 MasterStat

Бренд: Water Furnace Страницы: 44

Cutler-Hammer Jockey

Бренд: Eaton Страницы: 12

Real Living iM1

Бренд: Yale Страницы: 2

Бренд: Petique Страницы: 44

ZITON RADIO LOOP MODULE

Бренд: EMS Страницы: 26

Бренд: Danfoss Страницы: 30

CIATControl OPC Server

Бренд: CIAT Страницы: 32

Бренд: Danfoss Страницы: 8

Infi 90 IMAOM01

Бренд: Bailey Страницы: 44

Бренд: Lauda Страницы: 40

Бренд: schmersal Страницы: 6

MultiConnect Dragonfly MTQ-MNA1-B01

Бренд: Multitech Страницы: 45

Бренд: Daikin Страницы: 8

Бренд: Silverline Страницы: 16

Бренд: Ravel Страницы: 33

Бренд: L&L KILNS Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды