Panasonic fp2/fp2sh Скачать руководство пользователя страница 197

Страница: 197 / 374

FP2/FP2SH Operation

FP2/FP2SH

−

6.7 FP2SH ROM Operation

6.7.3

Precautions When Operating the ROM

Precautions Before Turning On the Power Supply

At the point when the ROM is installed, be aware that operation differs as described below,

depending on the setting of the DIP switches on the back of the CPU.

If the power supply is turned on when DIP switch SW2 is on and SW4 is off:

When the power supply is turned on, the contents of the memory (ROM) are automati-

cally transferred to the internal RAM and written there. Be aware that the previous

contents of the RAM will be lost at that point.

If the power supply is turned on when DIP switch SW2 is off:

Even if the memory (ROM) is installed, the contents of the internal RAM can be read

using the programming tools.
Consequently, to confirm the contents of the memory (ROM), the contents of the ROM

should be sent to the internal RAM.
To continue using ROM operation, turn off the power supply, and set DIP switch SW2

to the “on” position and SW4 to the “off” position. Then turn the power supply on again.

Содержание fp2/fp2sh























































































































































































































































































































































































Результаты поиска

Содержание fp2/fp2sh

Отзывы:

Похожие инструкции для fp2/fp2sh

Бренды по названию

Популярные бренды

Panasonic fp2/fp2sh, Руководство пользователя

Результаты поиска

Содержание fp2/fp2sh

Отзывы:

Похожие инструкции для fp2/fp2sh

Бренды по названию

Популярные бренды