Panasonic fp2/fp2sh Скачать руководство пользователя страница 156

Страница: 156 / 374

FP2/FP2SH

Installation and Wiring

−

4.4

Wiring the Connector Type I/O Units

Assembly of Connector for Wire-pressed Terminal Cable

The wire end can be directly press-fitted without removing the wire’s insulation, saving

labor.

Procedure:

Bend the contact back from the carrier, and set it in the

pressure connection tool.

Insert the wire without removing its insulation until it

stops, and lightly grip the tool.

After press-fitting the wire, insert it into the housing.

When all wires has been inserted, fit the semi-cover into place.

Содержание fp2/fp2sh























































































































































































































































































































































































Результаты поиска

Содержание fp2/fp2sh

Отзывы:

Похожие инструкции для fp2/fp2sh

Бренды по названию

Популярные бренды

Panasonic fp2/fp2sh, Руководство пользователя

Результаты поиска

Содержание fp2/fp2sh

Отзывы:

Похожие инструкции для fp2/fp2sh

Бренды по названию

Популярные бренды