Panasonic fp2/fp2sh Скачать руководство пользователя страница 187

Страница: 187 / 374

FP2/FP2SH Operation

FP2/FP2SH

−

6.4

Writing to ROM

Verify that the SW2 of operation condition switches (DIP

switches) on the back of the CPU are set to RAM opera-

tion position (off).

FP2 CPU

rear side

SW2
Program memory selector

off: RAM operation

on: ROM operation

[

]

off

Reattach the CPU to it original position on the back-

plane.

B. Clearing the program within the CPU

Note

If inputting of the program is done without first performing this

operation, the contents of the internal RAM of CPU may become

improper.

Operations using FPWIN GR

On the “Online” menu, select “Online Edit Mode”.

On the “Edit” menu, select “Clear Program”.

Содержание fp2/fp2sh























































































































































































































































































































































































Результаты поиска

Содержание fp2/fp2sh

Отзывы:

Похожие инструкции для fp2/fp2sh

Бренды по названию

Популярные бренды

Panasonic fp2/fp2sh, Руководство пользователя

Результаты поиска

Содержание fp2/fp2sh

Отзывы:

Похожие инструкции для fp2/fp2sh

Бренды по названию

Популярные бренды