Panasonic fp2/fp2sh Скачать руководство пользователя страница 147

Страница: 147 / 374

Installation and Wiring

FP2/FP2SH

−

4.2

Power Supply Wiring

4.2.2

Grounding

Always ground the FP2/FP2SH PLC.
Ground the unit with the ground terminal as illustrated below.

Ground terminal

For grounding purposes, use ground wires with a minimum of 2mm

(AWG14) and the

grounding connection should have a resistance of less than 100

The point of grounding should be as close to the FP2/FP2SH PLC as possible. The

ground wire should be as short as possible.
If two devices share a single ground point, it may produce an adverse effect. Always

use an exclusive ground for each device.

Other
device

FP2/FP2SH
PLC

Other
device

CORRECT

FP2/FP2SH
PLC

Содержание fp2/fp2sh























































































































































































































































































































































































Результаты поиска

Содержание fp2/fp2sh

Отзывы:

Похожие инструкции для fp2/fp2sh

Бренды по названию

Популярные бренды

Panasonic fp2/fp2sh, Руководство пользователя

Результаты поиска

Содержание fp2/fp2sh

Отзывы:

Похожие инструкции для fp2/fp2sh

Бренды по названию

Популярные бренды