Panasonic fp2/fp2sh Скачать руководство пользователя страница 251

Страница: 251 / 374

Maintenance

FP2/FP2SH

−

9.1 Replacement of Spare Parts

Procedure for FP2SH

Lift up the lead wire.

Make sure the lead wire next to the connector insertion

area, which is also the battery holder, is lifted out of the

hole that secures it in place.

Lift up the battery.

Pull the connector off.

Pull the connector straight off, so the terminals do not

bend.

Install the new battery by reversing the above proce-

dure.

Make sure the connector terminals are positioned in the

correct directions.

Содержание fp2/fp2sh























































































































































































































































































































































































Результаты поиска

Содержание fp2/fp2sh

Отзывы:

Похожие инструкции для fp2/fp2sh

Бренды по названию

Популярные бренды

Panasonic fp2/fp2sh, Руководство пользователя

Результаты поиска

Содержание fp2/fp2sh

Отзывы:

Похожие инструкции для fp2/fp2sh

Бренды по названию

Популярные бренды