Panasonic fp2/fp2sh Скачать руководство пользователя страница 206

Страница: 206 / 374

FP2/FP2SH

FP2/FP2SH Operation

−

6.8

FP2SH IC Memory Card Operation (for FP2

−

C2P/FP2

−

C3P)

Executing Programs

There are two ways to execute programs written on IC memory cards, described below.

Programs are automatically transferred when the power supply is turned on.

If the power supply is turned on when the DIP switches on the back of the CPU

are set so that both SW2 and SW4 are on, the “Autoexec.spg” file stored in the IC

memory card is sent to the internal RAM. When the mode is switched to RUN,

operation begins in accordance with the contents of that file.

Internal RAM

Program

Data

Comment

Internal FROM

Data

Program

Autoexec.spg

IC memory card

FP2SH (FP2-C2P, FP2-C3P)

Sending programs from the “ROM & RAM service...” menu

If the power supply is turned on when the DIP switches on the back of the CPU

are set so that SW2 is off and SW4 is on, executing the “ROM

→

RAM” operation

causes the “Autoexec.spg” file stored in the IC memory card to be sent to the in-

ternal RAM. When the mode is switched to RUN, operation begins in accordance

with the contents of that file.

Before the “ROM

→

RAM” menu is executed, any contents loaded with the tool become

the contents of the internal RAM.

Содержание fp2/fp2sh























































































































































































































































































































































































Результаты поиска

Содержание fp2/fp2sh

Отзывы:

Похожие инструкции для fp2/fp2sh

Бренды по названию

Популярные бренды

Panasonic fp2/fp2sh, Руководство пользователя

Результаты поиска

Содержание fp2/fp2sh

Отзывы:

Похожие инструкции для fp2/fp2sh

Бренды по названию

Популярные бренды