Panasonic fp2/fp2sh Скачать руководство пользователя страница 180

Страница: 180 / 374

FP2/FP2SH

FP2/FP2SH Operation

−

6.1

FP2 Operation

6.1.1.2

Retaining the Data During Power Outages

For the operation memory, such as that for internal relays and data registers, the data

that is set as hold-type memory is backed up by the backup battery.

Note

If the internal relays and data registers are set to be non-hold

type, then they will not be saved.

Battery-less operation

During ROM operation, if it is not necessary to retain the internal relays and data regis-

ters, then you can set them all to non-hold type and perform operation without a backup

battery.

6.1.1.3

Setting the Battery Error Warnings

Under normal conditions, if an error occurs with the backup battery, the BATT. and ER-

ROR LEDs on the front of the CPU are on for battery error warning. With ROM operation

that does not require the backup battery for operation memory, it is possible to set it so

that this warning is not given. With this setting, the BATT. and ERROR LEDs do not light.

Method

The programming tool software is required in order for this setting to be effective.

Procedure:

On the “Option” menu, select “PLC Configuration”.

Select “Initial Switch” tab.

Check “Alarm battery error” off.

Содержание fp2/fp2sh























































































































































































































































































































































































Результаты поиска

Содержание fp2/fp2sh

Отзывы:

Похожие инструкции для fp2/fp2sh

Бренды по названию

Популярные бренды

Panasonic fp2/fp2sh, Руководство пользователя

Результаты поиска

Содержание fp2/fp2sh

Отзывы:

Похожие инструкции для fp2/fp2sh

Бренды по названию

Популярные бренды