Panasonic fp2/fp2sh Скачать руководство пользователя страница 167

Страница: 167 / 374

Installation and Wiring

FP2/FP2SH

−

4.6

Safety Measures

4.6.2

Momentary Power Failures

If the duration of the power failure is less than 10 ms, the FP2/FP2SH continues to oper-

ate. If the power is off for 10 ms or longer, operation changes depending on the

combination of units, the power supply voltage, and other factors. (In some cases, op-

eration may be the same as that for a power supply reset.)

4.6.3

Alarm Output

The alarm output goes on when the watchdog timer is activated by a program error or

an error in the hardware itself.

The alarm output terminal has two relay contacts, N.O. (normally open) and N.C. (nor-

mally closed). This can be used as an external alarm signal when an error occurs.

Lamp for alarm

signal

Power supply unit

COM

Watchdog timer

The watchdog timer is a program error and hardware error detection timer. It goes on

when the scan time exceeds 640 ms.

When the watchdog timer is activated, at the same time the ALARM LED lights, the

ALARM contacts on the power supply unit go on, all outputs to the output units are

turned off and the unit is put in halted state. The system is in a non-processing state that

includes communications with programming tools as well.

Note

The ALARM contacts of the power supply unit installed on the

expansion backplane will not also operate.

Содержание fp2/fp2sh























































































































































































































































































































































































Результаты поиска

Содержание fp2/fp2sh

Отзывы:

Похожие инструкции для fp2/fp2sh

Бренды по названию

Популярные бренды

Panasonic fp2/fp2sh, Руководство пользователя

Результаты поиска

Содержание fp2/fp2sh

Отзывы:

Похожие инструкции для fp2/fp2sh

Бренды по названию

Популярные бренды