Panasonic fp2/fp2sh Скачать руководство пользователя страница 138

Страница: 138 / 374

FP2/FP2SH

Installation and Wiring

−

4.1

Installation

4.1.2.2

Units

Be sure to install the unit according to the following procedures.

Notes

•

Do not remove the dust proofing label that is attached to the

upper portion of the unit until the unit is completely installed

and the wiring is completed. However, be sure to remove the

dust proofing label prior to operation (

section 4.3.3).

•

Complete the backup battery installation and operation condi-

tion switches setting prior to installing the CPU (

sections

2.2.1 and 4.1.4).

1) FP2 backplane

•

With the CPU backplane, install in order from the left to the

right, the power supply unit, the CPU, the I/O and the intelli-

gent units.

With the expansion backplane, install in order from the left to

the right, the power supply unit, the I/O and the intelligent

units.

•

Install a power supply unit on to the expansion backplane as

well.

•

Do not install a CPU on to the expansion backplane.

2) FP2 backplane H type

•

The basic FP2 backplane that the CPU unit can be installed

and the expansion backplane that other various units can be

installed are available.

•

The positions to install a power supply unit, CPU unit and I/O

units are fixed. When using a 1

−

module type power supply

unit, a space of 1 module will be created between the power

supply unit and CPU unit, or between the power supply unit

and I/O units.

•

Do not put the wiring in the space in order to prevent the effect

of radiation noise.

•

Set the board No. setting switches on the expansion back-

plane.

•

A power supply unit is also necessary on an expansion back-

plane.

Содержание fp2/fp2sh























































































































































































































































































































































































Результаты поиска

Содержание fp2/fp2sh

Отзывы:

Похожие инструкции для fp2/fp2sh

Бренды по названию

Популярные бренды

Panasonic fp2/fp2sh, Руководство пользователя

Результаты поиска

Содержание fp2/fp2sh

Отзывы:

Похожие инструкции для fp2/fp2sh

Бренды по названию

Популярные бренды