Panasonic fp2/fp2sh Скачать руководство пользователя страница 146

Страница: 146 / 374

FP2/FP2SH

Installation and Wiring

−

4.2

Power Supply Wiring

Example of suitable pressure connection terminal

Manufacturer

Shape

Part number

Suitable wire

JST Mfg. Co., Ltd.

Round type

−

N3A

1.04 to 2.63mm

Fork type

−

MS3

Use wire that is thicker than 2mm

Power supply system

Use separate wiring systems for the FP2/FP2SH power supply unit output devices and

motorized devices.

Motorized
device

I/O device

Insulated
transformer

Breaker

PLC

Note

Use the same power supply system for the expansion backplane

and CPU backplane so that they are turned on and off simulta-

neously.

Power
suplly

unit

Power
suplly

unit

Simultaneous on and off

via the same power sup-

ply system.

CPU backplane

Expansion backplane

Eliminating effects from noise

Use a low noise power supply
There is sufficient noise resistance for superimposed noise in the power supply wiring,

however using an insulated transformer is recommended for further noise protection.
Twist the power supply wire to minimize the effects of noise.

Содержание fp2/fp2sh























































































































































































































































































































































































Результаты поиска

Содержание fp2/fp2sh

Отзывы:

Похожие инструкции для fp2/fp2sh

Бренды по названию

Популярные бренды

Panasonic fp2/fp2sh, Руководство пользователя

Результаты поиска

Содержание fp2/fp2sh

Отзывы:

Похожие инструкции для fp2/fp2sh

Бренды по названию

Популярные бренды