Panasonic fp2/fp2sh Скачать руководство пользователя страница 200

Страница: 200 / 374

FP2/FP2SH

FP2/FP2SH Operation

−

6.7

FP2SH ROM Operation

The “ROM & RAM Service” window opens.

Select “ROM

←

RAM” and press the “Data” button.

The “Data Register Range Setup” window opens.

Select the data and specify the range.

Clicking on the check box in front of the data type speci-

fies whether or not that data can be sent. Data marked

with a check mark can be sent.

To specify the range, double

−

click on the list.

Storage Capacity of User ROM

The potential storage capacity of user ROM is:

Number of program step

Fixed value (2k words)

+ Data capacity

Total number of words

The largest total value of the above is 128k words.

Precautions for Comment Storage

Editing of the program cannot be done during ROM operation. Transfer the data after

set the DIP switches SW2 to off.

Содержание fp2/fp2sh























































































































































































































































































































































































Результаты поиска

Содержание fp2/fp2sh

Отзывы:

Похожие инструкции для fp2/fp2sh

Бренды по названию

Популярные бренды

Panasonic fp2/fp2sh, Руководство пользователя

Результаты поиска

Содержание fp2/fp2sh

Отзывы:

Похожие инструкции для fp2/fp2sh

Бренды по названию

Популярные бренды