Panasonic AJ-CX4000, Руководство по эксплуатации

Страница: 64 / 223

– 64 –
Chapter 4 Operation — Menu settings
(Factory setting: [L/M/H])
[DS.GAIN OFF]
Selects a method to release digital super gain mode (accumulated gain).
[L/M/H] The digital super gain mode is released in following cases.
f When the <GAIN> switch setting is changed
f When the USER button assigned with [DS.GAIN] is pressed
[DS.GAIN] The digital super gain mode is released only when the USER button assigned with [DS.GAIN] is pressed.
(Factory setting: [DS.GAIN])
[D.ZOOM]
Selects the zoom ratio for when the USER button assigned with [D.ZOOM] is pressed.
The items that can be set are as follows.
f [ × 2], [ × 3], [ × 4], [ALL]
(Factory setting: [ALL])
[USER SW]
The function to be assign to the USER button can be set.
Following functions can be assigned.
f [INHIBIT], [DRS], [FBC], [S.GAIN], [ATW], [ATW LOCK], [Y GET], [D.ZOOM], [DS.GAIN], [S.IRIS], [I.OVR], [S.BLK], [B.GAMMA], [FOCUS ASSIST],
[C.TEMP], [ADAPTIVE MATRIX], [PRE REC], [REC CHECK], [DEL LAST CLIP], [SLOT SEL], [REC SW], [WFM], [LCD/VF HDR], [LCD/VF DETAIL],
[VF COLOR], [INDICATOR SW], [LOAD SETUP FILE], [LCD BACKLIGHT], [CARD READER MODE], [STREAMING START]
For details, refer to “Assigning function to the USER buttons” (page 129).
[USER1] Sets the function to assign to the <USER 1> button.
(Factory setting: [FOCUS ASSIST])
[USER2] Sets the function to assign to the <USER 2> button.
(Factory setting: [S.GAIN])
[USER3] Sets the function to assign to the <USER 3> button.
(Factory setting: [DS.GAIN])
[USER4] Sets the function to assign to the <USER 4> button.
(Factory setting: [Y GET])
[USER5] Sets the function to assign to the <USER 5> button.
(Factory setting: [WFM])
[WHITE BALANCE MODE]
[FILTER INH]
Selects whether to hold or not hold the white balance memory (Ach and Bch) data for each CC filter.
[ON] Holds Ach and Bch memory data (two memories), regardless of the CC filter.
[OFF] Holds Ach and Bch memory data (eight memories), for each CC filter.
(Factory setting: [ON])
[SHOCKLESS AWB]
When the position of the <WHITE BAL> switch is changed, set the time until it transfers to the white balance condition at the changed position.
[FAST] Transfers to the white balance condition in approximately one second.
[NORMAL] Transfers to the white balance condition in approximately two seconds.
[SLOW1] Transfers to the white balance condition in approximately three seconds.
[SLOW2] Transfers to the white balance condition in approximately ten seconds.
[SLOW3] Transfers to the white balance condition in approximately 20 seconds.
[OFF] Transfers immediately.
(Factory setting: [NORMAL])
[AWB AREA]
Selects the detection area to perform the auto adjustment of the white balance.
[25%] Detects 25% of the area near screen center.
[50%] Detects 50% of the area near screen center.
[90%] Detects 90% of the screen area.
(Factory setting: [25%])
[ATW]
Assigns the setting of the auto tracking white balance function to the <WHITE BAL> switch.
The items that can be set are as follows.
f [Ach], [Bch], [PRE], [OFF]
(Factory setting: [OFF])