Oracle Netra SPARC S7-2 Скачать руководство пользователя страница 29

Страница: 29 / 258

Identify Disabled Components

Related Information

■

“Log In to Oracle ILOM (Service)” on page 26

■

“Identify Disabled Components” on page 29

■

“Device Paths” on page 20

■

“Interpreting LEDs” on page 30

Identify Disabled Components

You can run the

show disabled

command from the Oracle ILOM prompt to identify

components that have been disabled either intentionally, by a user, or automatically, because of

a fault.

At the Oracle ILOM prompt, type:

show disabled

Target | Property | Value
-----------------------------------+----------------+--------------------
...
/SYS/MB/CMP0 | disable_reason | Configuration Rules
...

For additional information about a disabled component, type the

show -t

command and the Oracle ILOM target.

See

“Device Paths” on page 20

For example, type:

show -t /SYS/MB/CMP0/MCU0/CH1/D0/

The target system paths here are examples. Your paths will vary.

Detecting and Managing Faults

Содержание Netra SPARC S7-2



































































































































































































































































Результаты поиска

Содержание Netra SPARC S7-2

Отзывы:

Oracle Netra SPARC S7-2, Руководство по обслуживанию, Страница: 29 / 258

Результаты поиска

Содержание Netra SPARC S7-2

Отзывы: