Oracle Netra SPARC S7-2 Скачать руководство пользователя страница 165

Страница: 165 / 258

Install a DIMM

If the DIMM does not easily seat into the connector socket, verify that the notch in the

DIMM is aligned with the connector key in the connector socket. If the notch is not

aligned, damage to the DIMM might occur.

Replace the air baffle.

(Optional) Use Oracle ILOM to clear server DDR4 DIMM faults.

DDR4 DIMM faults are automatically cleared after a new DIMM has been installed. If you

need to manually clear DDR4 DIMM faults, refer to the Oracle Integrated Lights Out Manager

(ILOM) 3.2 Documentation Library at

http://www.oracle.com/goto/ILOM/docs

Return the server to operation.

See

“Returning a Server to Operation” on page 235

Verify the DIMM.

See

“Verify a DIMM” on page 166

Related Information

■

“Understanding DIMM Layout and Population Rules” on page 160

■

“Locate a Faulty DIMM” on page 161

■

“Remove a DIMM” on page 163

Servicing DIMMs

165

Содержание Netra SPARC S7-2



































































































































































































































































Результаты поиска

Содержание Netra SPARC S7-2

Отзывы:

Oracle Netra SPARC S7-2, Руководство по обслуживанию, Страница: 165 / 258

Результаты поиска

Содержание Netra SPARC S7-2

Отзывы: