Oracle Netra SPARC S7-2 Скачать руководство пользователя

Страница: 167 / 258

Verify a DIMM

Switch to the system console to view POST output.

Watch the POST output for possible fault messages. This output indicates that POST did

not detect any faults:

start /HOST/console

...
0:0:0>INFO:
0:0:0> POST Passed all devices.
0:0:0>POST: Return to VBSC.
0:0:0>Master set ACK for vbsc runpost command and spin...

Note -

The server might boot automatically at this point. If so, go to

Step 3f

. If the server

remains at the OpenBoot prompt (

) go to the next step.

If the server remains at the OpenBoot prompt, type

boot

Return the virtual keyswitch to Normal mode.

set /HOST keyswitch_state=Normal

Set 'keyswitch_state' to 'Normal'

Switch to the system console and type:

fmadm faulty

If any faults are reported, refer to the diagnostics instructions described in

“Detecting and

Managing Faults” on page 25

Switch to the Oracle ILOM command shell.

Type:

show faulty

Servicing DIMMs

167

Содержание Netra SPARC S7-2



































































































































































































































































Результаты поиска

Содержание Netra SPARC S7-2

Отзывы:

Похожие инструкции для Netra SPARC S7-2

Бренды по названию

Популярные бренды

Oracle Netra SPARC S7-2, Руководство по обслуживанию

Результаты поиска

Содержание Netra SPARC S7-2

Отзывы:

Похожие инструкции для Netra SPARC S7-2

Бренды по названию

Популярные бренды