Oracle Netra SPARC S7-2 Скачать руководство пользователя страница 89

Страница: 89 / 258

Remove a SAS Drive

Check the

Fault class

and

Description

fields for more information.

If a drive is faulty, replace it.
See

“Remove a SAS Drive” on page 89

If you are unable to determine if a drive is faulty, seek further information.

See

“Detecting and Managing Faults” on page 25

Related Information

■

“Remove a SAS Drive” on page 89

■

“SAS Drive Configuration” on page 86

■

“SAS Drive LEDs” on page 86

■

“Verify a SAS Drive” on page 95

■

“Detecting and Managing Faults” on page 25

Remove a SAS Drive

Removing a SAS drive is a hot-swap operation. You must run commands on the server before

you remove the drive.

Follow safety and ESD precautions.

See

“Preparing for Service” on page 43

Determine which drive to remove.

See

“Locate a Faulty Drive” on page 87

Tilt and pivot the air filter away from the server.

See

“Remove the Filter” on page 79

Determine if you need to shut down the OS to remove the drive, then perform

one of these actions.

■

If the drive cannot be taken offline without shutting down the OS, follow

instructions in

“Power Off the Server (Power Button - Graceful)” on page 51

then go to

Step 7

■

If the drive can be taken offline without shutting down the OS, go to

Step 5

Servicing SAS Drives

Содержание Netra SPARC S7-2



































































































































































































































































Результаты поиска

Содержание Netra SPARC S7-2

Отзывы:

Oracle Netra SPARC S7-2, Руководство по обслуживанию, Страница: 89 / 258

Результаты поиска

Содержание Netra SPARC S7-2

Отзывы: