Oracle Netra SPARC S7-2 Скачать руководство пользователя

Страница: 101 / 258

Power On an NVMe Drive and Attach a Device Driver

Consider your next step.

■

If adding a drive to an empty slot, remove the drive filler.

■

If replacing a faulty NVMe drive, remove the drive.

See

“Remove an NVMe Drive” on page 99

Align the new drive with the drive slot.

The drive is physically addressed according to the slot in which it is installed. You must install a

replacement drive in the same slot as the drive that was removed.

Slide the drive into the slot until the drive is fully seated.

Rotate the air filter up until the latches click.

See

“Install the Filter” on page 82

Close the drive latch to lock the drive in place.

Power on the drive and attach a device driver.

See

“Power On an NVMe Drive and Attach a Device Driver” on page 101

Related Information

■

“Power On an NVMe Drive and Attach a Device Driver” on page 101

■

“Verify the Operation of an NVMe Storage Drive” on page 102

Power On an NVMe Drive and Attach a Device Driver

This task uses

pcie13

as an example.

Enable the drive slot.

hotplug enable pcie

where

is the slot number. See

“Device Paths” on page 20

Display the status of the NVMe drive.

Note -

The state of the slot must be

Enabled

hotplug list –lc

Servicing NVMe Storage Drives

101

Содержание Netra SPARC S7-2



































































































































































































































































Результаты поиска

Содержание Netra SPARC S7-2

Отзывы:

Похожие инструкции для Netra SPARC S7-2

Бренды по названию

Популярные бренды

Oracle Netra SPARC S7-2, Руководство по обслуживанию

Результаты поиска

Содержание Netra SPARC S7-2

Отзывы:

Похожие инструкции для Netra SPARC S7-2

Бренды по названию

Популярные бренды