background image

Verify the Drive Backplane

See:

“Returning a Server to Operation” on page 235

“Verify the Drive Backplane” on page 124

Related Information

“Detecting and Managing Faults” on page 25

“Returning a Server to Operation” on page 235

Verify the Drive Backplane

After you install the drive backplane, you can verify its functionality.

1.

Access Oracle ILOM.

See 

“Log In to Oracle ILOM (Service)” on page 26

.

2.

Reset the drive backplane.

-> 

set /SYS/DBP clear_fault_action=true

Are you sure you want to clear /SYS/DBP (y/n)? 

y

Set 'clear_fault_action' to 'true'

->

3.

Verify that the drive backplane is not faulty, then return to this procedure.

See 

“Determine if the Drive Backplane Is Faulty” on page 118

.

4.

Verify that the installed drives are recognized.

-> 

show /SYS/DBP

 /SYS/DBP
  Targets:
   HDD0
   HDD1
   HDD2
...
->

Related Information

“Determine if the Drive Backplane Is Faulty” on page 118

“Detecting and Managing Faults” on page 25

124

Netra SPARC S7-2 Server Service Manual • February 2017

Содержание Netra SPARC S7-2



































































































































































































































































Отзывы: