manualshive.com logo in svg

Oracle Netra SPARC S7-2, Руководство по обслуживанию, Страница: 26 / 258

Поделиться
Скачать
Oracle Netra SPARC S7-2 Скачать руководство пользователя страница 26

Log In to Oracle ILOM (Service)

Step

Description

Links

2.

Run the 

show disabled

 command to

display information about components

that have been disabled either

intentionally or because of a failure.

Plan to service any components that are

degraded or might need service soon to

minimize system downtime.

“Identify Disabled Components” on page 29

3.

Identify the names of components that

require service as reported by diagnostic

software.

“Device Paths” on page 20

Related Information

■

“Performing Advanced Troubleshooting” on page 34

■

“Clear a Fault Manually” on page 40

■

“Interpreting LEDs” on page 30

Log In to Oracle ILOM (Service)

At the terminal prompt, type:

ssh root@

SP-IP-address

Password: 

password

Oracle (R) Integrated Lights Out Manager
Version 3.2.x
Copyright (c) 2016, Oracle and/or its affiliates, Inc. All rights reserved.
->

Related Information

■

“Identify Faulted Components” on page 27

■

“Identify Disabled Components” on page 29

■

“Device Paths” on page 20

■

“Interpreting LEDs” on page 30

26

Netra SPARC S7-2 Server Service Manual • February 2017

Содержание Netra SPARC S7-2



































































































































































































































































Отзывы:

Нет отзывов