Oracle Netra SPARC S7-2 Скачать руководство пользователя страница 105

Страница: 105 / 258

Remove the eUSB Drive

See

“Identify Faulted Components” on page 27

Check the

Fault class

and

Description

fields for more information.

If an eUSB drive is faulty, replace it.

See

“Remove the eUSB Drive” on page 105

If you are unable to determine if an eUSB drive is faulty, seek further information.

See

“Detecting and Managing Faults” on page 25

Related Information

■

“Identifying Components” on page 13

■

“Detecting and Managing Faults” on page 25

■

“Remove the eUSB Drive” on page 105

Remove the eUSB Drive

Prepare for servicing.

See

“Preparing for Service” on page 43

Loosen the screw that attaches the eUSB drive to the motherboard.

Save the screw to use with the new eUSB drive.

Servicing the eUSB Drive

105

Содержание Netra SPARC S7-2



































































































































































































































































Результаты поиска

Содержание Netra SPARC S7-2

Отзывы:

Oracle Netra SPARC S7-2, Руководство по обслуживанию, Страница: 105 / 258

Результаты поиска

Содержание Netra SPARC S7-2

Отзывы: