Oracle Netra SPARC S7-2 Скачать руководство пользователя страница 210

Страница: 210 / 258

Install NVMe Cables

The cable labeled 0-1 must be connected to the port labeled 0-1 on the motherboard, and

the cable labeled 2-3 must to the port 2-3 on the motherboard.

Install the SAS cables.

See

“Install the SAS Drive Signal Cable” on page 197

and

“Install HBA SAS

Cables” on page 213

Install the air duct.

See

“Install the Air Duct” on page 236

Return the server to operation.

See

“Returning a Server to Operation” on page 235

Related Information

■

Oracle 1.6TB NVMe SSD Documentation Library

■

“Component Locations (Storage, Power, NVMe, and Fan Modules)” on page 14

■

“Component Locations (Motherboard, Memory, and PCIe Cards)” on page 16

■

“Preparing for Service” on page 43

■

“Returning a Server to Operation” on page 235

210

Netra SPARC S7-2 Server Service Manual • February 2017

Содержание Netra SPARC S7-2



































































































































































































































































Результаты поиска

Содержание Netra SPARC S7-2

Отзывы:

Oracle Netra SPARC S7-2, Руководство по обслуживанию, Страница: 210 / 258

Результаты поиска

Содержание Netra SPARC S7-2

Отзывы: