Express5800/R110i-1
First Edition, Apr
2017
Be sure to read this guide carefully before using this
server and keep this guide for future use.
Read and follow
Safety Precautions and Regulatory Notices
that comes with this product first.
The following describes the procedures from opening the carton box to
starting using this product. Be sure to follow these steps.
Step 1
Check the accessories
Open the carton box, and then make sure you have all the accessories listed below:
●
Express5800/R110i-1 server × 1
●
Getting Started (this guide) × 1
●
Safety Precautions and Regulatory Notices × 1
●
SDR Update CD-ROM × 1
●
Power cord × 1 or × 2*
●
Front Bezel × 1
●
Cable ties (for securing AC power cord) × 1 or × 2*
●
The tool used for removing slide rails (outer rails) × 1
Important: Keep accessories for future use.
* EXP335A only
Step 2
Install internal optional devices
Install internal optional devices. Go to Step 3 if you have not purchased optional
devices or if you purchased a Build to Order (BTO) product.
Note: See “Installing Internal Optional Devices” in
User’s Guide
and the manual that comes with
the optional device.
Step 3
Place the product to a proper location
Install the server into a rack under the following conditions.
Note: For details on how to install the server in the rack, see “Installation and Connection” in
User’s Guide
.
Step 4
Connect cables
Connect cables to the server.
Note: For details on how to install the server in the rack, see “Installation and Connection” in
User’s Guide
.
*1 Connect the power cord to a circuit breaker of up to 15A.
To prevent power cord from disconnecting, secure the power cord with the provided cable tie.
Getting Started!
Environment:
<Operating>
Ambient temperature:5°C to 40°C*
Humidity: 10% to 85%
Temperature gradient: ±10°C/hour
Air pressure: 749 to 1040 hpa
<Non-operation>
Ambient temperature: 5°C to 40°C*
Humidity: 10% to 85%
Temperature gradient: ±15°C/hour
Air pressure: 749 to 1040
hpa±15°C/hour
Air pressure: 749 to 1040 hpa
*: 5°C to 45°C (when an optional kit is installed;
subject to composition restrictions)
Outlet or UPS is within reach
of the attached power cord
Attach
stabilizers
When using
multiple racks, be
sure to join them
Leave the minimum clearance
around the rack: 1 m to the
front/rear, 60 cm to the sides, and
40 cm above the top
Do not use the server in an environment where
corrosive gas is present.
Flat and solid floor
100/200VAC bipolar
grounded outlet or bipolar
outlet with ground terminal
or UPS
Instruction Manuals
Instruction manuals are available at NEC Web Site (http://www.nec.com/).
To see the manuals in EXPRESSBUILDER, follow the steps below.
(1) If you already have the EXPRESSBUILDER DVD, set the DVD into a computer
running Windows. Follow the on-screen messages to start the menu, and then go
to (4).
Tips: You can download EXPRESSBUILDER from NEC Web Site.
(2) To install Windows, follow this guide (reverse side).
(3) After installing Windows, click
NEC EXPRESSBUILDER
on the desktop or Start
Menu.
(4) Click
Instruction Manuals
on the following menu.
USB device
Front
Display unit
Finally, connect the
power cord to an outlet.*
1
For connecting to the
UPS, refer to the next
section.
Rear
Ports for data transmission
1000BASE-T
100BASE-TX
10BASE-T
Device with the
serial interface
Management
LAN connector
1000BASE-T
100BASE-TX
10BASE-T
Hub, switching
hub, ...
USB device
USB device
USB device
Hub, switching
hub, ...
