142
Error Log
Section 8-2
Note
(1) Errors indicated by error codes 0101 to 0116 Hex are logged only when
the frame was discarded because transmission was impossible.
(2) Errors indicated by error codes 0220 to 0223 Hex are logged at the same
time as error code 0206 or 0207 Hex (participating nodes reduced). You
can determine the nodes removed from the network. For example, if node
16 is removed, the following error codes will be generated.
Error Status
The status of each bit indicates that an error has occurred as given in the dia-
gram below.
8-2-3
Reading and Clearing Error Logs
Error logs can be read or cleared using the CX-Net, or the message service.
The following commands can be used for the message service.
Reading an Error Log
Send the ERROR LOG READ FINS command (command code 2102) to the
appropriate node. Refer to
6-4-11 ERROR LOG READ
.
Clearing an Error Log
Send the ERROR LOG CLEAR FINS command (command code 2103) to the
appropriate node. Refer to
6-4-12 ERROR LOG CLEAR
.
021C
Hex
Data link error inactive
Not set
Restart the SYSMAC LINK
Unit.
Yes
021D
Hex
Data link table communications
cycle time setting error
Communica-
tions cycle
time set in the
data link sta-
tus (Unit: ms,
2-digit hexa-
decimal)
Minimum
possible
communica-
tions cycle
time setting
(Unit: ms, 2-
digit hexa-
decimal)
Set the data link tables com-
munications cycle time auto-
matically, or increase the
settings manually.
Yes
0220
Hex
Participating nodes reduced
(removed node information)
Node 1 to 16 removed
(correspond to bits 0 to 15)
Check the network parame-
ters, cables, and terminal
resistance settings.
Yes
0221
Hex
Node 17 to 32 removed
(correspond to bits 0 to 15)
0222
Hex
Node 33 to 48 removed
(correspond to bits 0 to 15)
0223
Hex
Node 49 to 62 removed
(correspond to bits 0 to 13)
0300
Hex
Packet discarded
Not set
Conduct an echoback test
and find the cause of the
error.
No
0601
Hex
Unit error
Not set
Check the operating environ-
ment.
Yes
Error
code
Contents
Detail code
Correction
Written to
EEPROM
1st byte
2nd byte
Error code
Information
Meaning
0206 Hex
3E01 Hex
Single node removed from system.
0221 Hex
0001 Hex
Node 16 removed from system.
1: Token timeout error
1: Polling timeout error
1: Communications controller hardware error
1: Polling node was changed
1: Nodes in Network changed (added or removed)
1: Communications controller send error
1: Node address duplication error
Содержание CS1W-SLK11-21 - 06-2004
