Omron 3G3AX-MX2-PRT-E Скачать руководство пользователя страница 30

Страница: 30 / 116

How to mount the Option Board on the Inverter

Section 2-3

Step 5

Move the Option Board Cable (no.2)
to the left with your finger, so the
Option Board Cable is not pinched
between the Option Board and the
Inverter Front Cover.

Note

Prevent a pinched Option Board
Cable, as shown in position A.

Note

Do not pull on the Option Board
Cable.

Note

Do not let the Option Board hang on
the Option Board Cable.

Insert the Option Board approximately 1 cm above the down-position into the
Front cover of the Inverter. See figure 1above.

Slide the Option Board down. See figure 2 above.

The snap-fits of the Option Board
(no.5) will be locked by the snap-fits
in the Front cover (no.4).

Connector

Option Board bottom side

I111E-EN-02+3G3AX-MX2-RX-PRT+OperManual.book Seite 16 Donnerstag, 8. September 2011 11:53 11

Содержание 3G3AX-MX2-PRT-E





















































































































Результаты поиска

Содержание 3G3AX-MX2-PRT-E

Отзывы:

Похожие инструкции для 3G3AX-MX2-PRT-E

Бренды по названию

Популярные бренды

Omron 3G3AX-MX2-PRT-E, Руководство пользователя

Результаты поиска

Содержание 3G3AX-MX2-PRT-E

Отзывы:

Похожие инструкции для 3G3AX-MX2-PRT-E

Бренды по названию

Популярные бренды