Omron 3G3AX-MX2-PRT-E Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 116

background image

xii

Application Precautions

!WARNING

Failure to observe these precautions could lead to serious or possibly fatal
injury. Always read these precautions.

• Check any user program in the system that acts as a PROFIBUS master

before actually running it. Not checking the program may result in unex-
pected operation.

• A revision AAAA Inverter allows the motor to run immediately if a trip con-

dition is reset, and at the same time, a run command is active via PROFI-
BUS. For safe operation clear the run command via PROFIBUS as soon
as a trip condition is detected. Refer to section

1-1-2 Inverter Support

to

determine the Inverter revision.

!Caution

Failure to observe these precautions could lead to faulty operation of the
Option Board or the Inverter, or could damage to either of the two. Always
read these precautions.

• Check the Inverter settings for proper Inverter behavior before actually

operating the Inverter remotely via the PROFIBUS network.

• Check the Inverter's EzSQ program and its interaction with the PROFI-

BUS master before actually running it on the Inverter. Not checking the
program may result in unexpected operation.

• Confirm that no adverse effect will occur at the moment the PROFIBUS

master stops communicating with the Inverter or at the moment the PRO-
FIBUS master has not yet started communicating to the Inverter.

• Confirm that no adverse effect will occur in the Inverter before force-set-

ting/force-resetting any bit in the system that acts as a PROFIBUS mas-
ter.

I111E-EN-02+3G3AX-MX2-RX-PRT+OperManual.book Seite xii Donnerstag, 8. September 2011 11:53 11

«
...
10
11
12
13
14
...
»

Содержание 3G3AX-MX2-PRT-E





















































































































Отзывы:

Нет отзывов

Похожие инструкции для 3G3AX-MX2-PRT-E

Бренд: ZALMAN Страницы: 20

Бренд: NXP Semiconductors Страницы: 24

Бренд: Ruckus Wireless Страницы: 56

Бренд: Renesas Страницы: 6

PG-FLEX RT FRL-752

Бренд: PairGain Страницы: 6

FRDM-STBC-SA9500

Бренд: Freescale Semiconductor Страницы: 2

Бренд: Roland Страницы: 2

Бренд: Realtek Страницы: 30

eBOX532-100-FL Series

Бренд: AXIOMTEK Страницы: 2

RCO-3000 Series

Бренд: C&T Solution Страницы: 96

UniFi Cloud Key

Бренд: Ubiquiti Страницы: 13

Бренд: Sangoma Страницы: 6

Бренд: PMD Страницы: 74

Бренд: Arbor Technology Страницы: 8

TeleCLIENT TC7730 Series

Бренд: ETL Страницы: 83

Бренд: Airlink101 Страницы: 46

Бренд: UMAX Technologies Страницы: 27

Бренд: Intel Страницы: 44

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды